![]() ![]() Metal stake should be similar to original stake (down to, but not touching bearing). Reposition pulley on support to ensure full support under staking pin. With pulley on support, use Bearing Staking Guide (J-33019-1) and Bearing Staking Pin (J-33019-2) to stake pulley in 3 places, 120 degrees apart. Install bearing in pulley using hammer, Bearing Installer (J-9481-A) and Handle (J-29886). DO NOT support pulley rim on flat surface, or pulley will be damaged. To install pulley bearing, place pulley on Support (J-21352-A). ![]() NOTE:To ensure proper bearing clearance, it is necessary to remove old stake metal before installing new bearing. Using a 1/8" punch, stake clutch coil inner ring in 3 places, 120 degrees apart. Ensure clutch coil and installer stay lined up during installation. Using Puller Adapter (J-33024) and Puller Bar (J-8433-1), press clutch coil onto compressor. Remove clutch coil using Puller Adapter (J-33023-A) and 2-jaw puller.Īlign reference marks made during removal. Scribe marks on compressor and clutch coil for installation reference. Use a hammer and Bearing Remover (J-9398-A) to drive bearing from pulley. With puller still engaged in pulley slots, invert assembly onto a solid flat surface. If bearing is to be removed on compressor with conventional mount, remove forcing screw from puller. Bearing removal and installation for compressor with direct mount is not available from manufacturer. NOTE:On compressor with conventional mount, it is not necessary to remove staking in front of bearing before removing bearing. Tighten puller and remove pulley assembly. Position Pulley and Bearing Puller (J-41552 for HD6/HT6/HU6 and HD6/HR-6HE or J-33020 for V5 or V7 compressor) into inner circle of slots on pulley assembly. Install Puller Guide (J-33023-A) on front head. Ensure forcing tip on remover/installer center screw is flat or end of shaft/axial plate will be damaged. Hold remover body and turn center screw into remover body to remove clutch plate and hub. On all compressors, using Clutch Plate Remover/Installer (J-33013-B), remove compressor clutch plate and hub. Use Clutch Plate Spanner (J-33027-A) to hold clutch plate and remove compressor shaft nut using Shaft Nut Socket (J-33022). ![]() On V5 or V7 compressor, remove dust cover (if equipped). Place compressor in Holding Fixture (HD6/HT6/HU6 and HD6/HR-6HE compressor use J-33026 on V5 or V7 compressor use J-34992 or J-41790). Please let us know what happens.ĬAUTION:DO NOT hammer on compressor shaft to remove clutch plate, as compressor damage will result. Expansion Valve: The AC expansion valve, which regulates refrigerant flow, could be clogged, causing the AC system’s pressure to be too low, and the compressor’s clutch fails to engage.Check out the diagrams (Below).Worn Bearings: The AC compressor can’t operate correctly with faulty bearings, as a result, the clutch will not engage correctly due to the restriction in the movement of the assembly’s clutch. ![]() Electrical Issues: Electrical issues such as a blown fuse for the ac clutch or a damaged wire could also prevent the AC clutch from engaging.Refrigerant Level: The low refrigerant level in the AC might not engage the compressor.The pressure switch, which senses the refrigerant pressure in the AC system, could be faulty, preventing the clutch from receiving its operational commands. Pressure Switch: One of the important factors is the pressure switch.Also, check the electric wire in case of bad clutch coil symptoms. Clutch Coil: The clutch coil, which provides power to the clutch plate, could be damaged or burned out, which can’t engage the compressor clutch.The compressor works to maintain the desired temperature inside the car by compressing and circulating the refrigerant gas, which absorbs heat from the air inside the car and releases it outside. When the AC clutch involves, it allows the compressor to spin and start circulating the refrigerant gas, which is essential for the air conditioning system to function. It is a component that stimulates and stops the compressor, which is responsible for compressing and circulating the refrigerant gas in the AC system. In an automotive air conditioning system, the AC clutch plays a crucial role in regulating the temperature inside the car. Frequently Asked Questions (FAQs) What Is AC Clutch Car AC Compressor Not Turning ON.Check For Low And High Refrigerant Pressure Start The Engine And Turn ON The AC And Blower Motor: 10 Easy Steps To Fix Car AC Compressor Clutch Not Engaging.How To Fix An AC Compressor Clutch Not Engaging.Why My AC Clutch is Not Engaging: Common Reasons.Importance of Air Conditioner Compressor Clutch. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |